Category: Roofing Repairs

  • Top 3 Roof Leak Repairs Residential Contractors Get Calls About

    Top 3 Roof Leak Repairs Residential Contractors Get Calls About

    As a homeowner, you’d like your roof to maintain its integrity over the years but common wear and tear and following roof leaks are inevitable. Roof leak repairs are simply part of the roof’s life.

    While there are many reasons for a roof’s deterioration, some roof areas are more prone to leaking than others. Skylights, chimneys, and vent pipes all provide an opportunity for moisture to get through, especially in older roofs or when they have not been installed properly.

    Residential Roofing: 3 Most Common Roof Leak Repairs

    Residential Roofing: 3 Most Common Roof Leak Repairs

    1. Roof Leak Repairs: Leaky Skylight

    A leaky skylight can be a homeowner’s worst nightmare. More often than not, an improper installation is the cause of a leak. If that’s the case, your local roofing contractor must handle the repairs to avoid further damage.

    Some common situations that cause skylights to leak are improperly installed fasteners, poor flashing seals, glass micro-fractures or fissures, and sealant failure due to thermal expansion. If the skylight leak is at the roof flashing, it may be possible to make temporary repairs using roof flashing cement around the perimeter of the unit. However, proper repairs will require removing shingles near the skylight, installing appropriate flashing, and reinstalling new shingles in the area. Most skylights have integral flashing or a special flashing kit that is specifically designed for the skylight and roofing material.

    A thorough roofing inspection will help your roofer uncover any problems with your skylights and suggest appropriate repairs so that should be your first step.

    New Roof & Velux Skylights Installation, Newark DE 19713

    2. Roof Leak Repairs: Chimney Flashing

    Damage to the chimney structure is quite common as well, as chimneys can develop cracks and crevices that allow water to permeate them. Instead of keeping rain and snow out of the roof seams, sub-par flashing allows moisture into the roof’s inner structure. Water seepage can cause mildew, mold, and premature aging of the roof.

    To fix this problem, start with a thorough inspection of your chimney base and walls looking for gaps, cracks, and obvious wear and tear. Chimney flashing needs to be replaced when it becomes rusty, corroded, chipped, or broken. Masonry caulk can seal small gaps or holes on a short-term basis but is not designed to take the place of the flashing. Depending on what you find, roofing cement, caulking, and more often than not flashing will need to be replaced.

    Since improperly installed flashing leaves your home unprotected from rain and snow it is always best to have a professional roofer address more extensive flashing problems.

    Chimney Flashing Repair, Wilmington DE 19803

    3. Roof Leak Repairs: Vent Pipe Repairs

    Aside from skylights and chimneys, roof vents are one of the most common causes of roof leaks. Rusty and cracked vent pipe collars around their base allow the water to first pool around, then seep through the interior walls of your home.  Again deteriorated flashing & old roof cements & sealants might be the reason behind vent pipe leaks.

    Occasionally, vent pipe leaks can also occur at the collar surrounding the base of the vent pipe where it breaks through the surface of the roofing material. When this occurs, rainwater can seep in between the rubber boot and the vent pipe and accumulate in your home, causing damage. If the rubber boot collar is cracked or damaged, it will need to be replaced.

    Need a Pro to Handle Your Roof Leak Repairs?

    If your roof is leaking contact a professional roofer for an inspection and repairs.

    Contact All Roofing Solutions, your Delaware roofing repair contractor with over 15 years of experience examining and repairing all types of roof problems. We’re here to help with all your roofing needs and are available to assist you with roof leak repairs, new installations, and roofing inspections.

    To schedule your free consultation, call 302-725-ROOF (7663) in Delaware or 610-551-ROOF (7663) in Pennsylvania. Contact us today and receive a discount of 15% off any roofing repair job.

    Why Choose All Roofing Solutions

    • Customer Satisfaction GuaranteedFamily-owned and operated contractor
    • Fully licensed and insured for your protection
    • Over 25 years of experience with roofing & siding installation and repair
    • A+ rated BBB member
    • Complimentary Extended Material warranty
    • 30-year workmanship guarantee on full roof replacements
    • Lien Waiver to protect the homeowners from material liens
    • Own crew—no subcontractors!
    • Full-service roofer handling all types of residential and commercial roofing, windows & siding projects.
    • Most re-roofing projects are completed in one day.
    • Because we are efficient we are able to offer very competitive prices compared to large contractors with bigger overhead.
    • Each roofing/siding project includes a meticulously performed, post-roofing inspection. We want to make sure that your roof replacement is done correctly and that it meets your complete satisfaction.
    • The company owner supervises all projects to ensure high-quality workmanship.
    • Customer Satisfaction Guaranteed!
  • 2 Simple Steps to Mastering Leaky Skylight Repairs

    While beautiful and functional, skylights are prone to leaking. In fact, leaky skylight repairs are among the most common roof leak repairs seen in residential roofing. A leaky skylight isn’t just an eyesore; it may be an indication of more serious, hidden damage.

    If you notice a leak around your skylight, you’ll want to diagnose it and have skylight repairs performed as soon as possible. In some cases, a leak around the skylight may indicate a serious need for roofing repairs.

    Whether you’re a DIY enthusiast or just looking for clear guidance, we will show you how to fix a leaking Velux skylight for good (or any other skylight brand for that matter).

    2 Simple Steps to Mastering Leaky Skylight Repairs

    Step #1: Diagnosing Skylight Leaks

    The first step in any skylight repair is to identify the source of the leak with a thorough inspection. You’ll want to make sure the leak is not just excessive condensation that has moved along the underside of the glass and dripped down the side of the interior. This occurs more often in very cold climates, in single-glazed skylights, and in damp locations like bathrooms, kitchens, and greenhouses.

    If your Velux skylight opens, check that it is fully closed and that the weather seals are in good condition. In addition, think about whether the leak occurs only in winter, in fall, or when there is snow or ice on the roof. If so, then look behind the skylight for leaves, ice, snow, or other debris that might be blocking the downhill flow of water and causing it to back up under the roof shingles.

    You’ll also want to look carefully at your roofing, paying particular attention to vent flashing or other roof penetrations. A leak in these locations can travel quite a distance before finding its way to an indoor opening at the skylight. For roof and skylight inspections, hire a contractor skilled in roofing repairs.

    New Roof & Velux Skylights Installation, Newark DE 19713

    Step #2: How to Fix a Leaky Skylight

    Leaks at the insulated glass frame may have permitted water to enter the window structure, forcing it apart and damaging the seal of the insulated glass itself. If it’s determined that the insulating glass unit of the skylight has failed, you may be able to re-seal the unit against further water leakage. However, only a replacement of the skylight will remove the condensation and opaque skylight glass of a failed window unit.

    If the skylight leak is at the roof flashing, it may be possible to make temporary repairs using roof flashing cement around the perimeter of the unit. However, proper repairs will require removing shingles near the skylight, installing appropriate flashing, and reinstalling new shingles in the area. Most skylights have integral flashing or a special flashing kit that is specifically designed for the skylight and roofing material.

    Bonus Leaky Skylight Repairs Tips:

    1. Use roofing cement (can or tube) to seal any gaps or holes in the flashing.
    2. Apply 100% silicone caulking (tube) to seal leaks around the skylight lens.
    3. If your skylight is still leaking, replace/repair the metal flashing around the frame of the skylight.
    2 Simple Steps to Mastering Leaky Skylight Repairs

    We Offer Leaky Skylight Repair Services

    If you notice leaks around your skylight, contact All Roofing Solutions for a comprehensive leak evaluation. With 25 years of experience and are here to help with all your roofing needs, large and small. 

    For more information on how to fix a leaky skylight or to schedule a professional consultation, call 302-725-ROOF (7663) in Delaware or 610-551-ROOF (7663) in Pennsylvania. We offer Free Estimates and honest service, never take shortcuts, and ensure every step is done right!

    Why Choose All Roofing Solutions

    • Customer Satisfaction GuaranteedFamily-owned and operated contractor
    • Fully licensed and insured for your protection
    • Over 25 years of experience with roofing & siding installation and repair
    • A+ rated BBB member
    • Complimentary Extended Material warranty
    • 30-year workmanship guarantee on full roof replacements
    • Lien Waiver to protect the homeowners from material liens
    • Own crew—no subcontractors!
    • Full-service roofer handling all types of residential and commercial roofing, windows & siding projects.
    • Most re-roofing projects are completed in one day.
    • Because we are efficient we are able to offer very competitive prices compared to large contractors with bigger overhead.
    • Each roofing/siding project includes a meticulously performed, post-roofing inspection. We want to make sure that your roof replacement is done correctly and that it meets your complete satisfaction.
    • The company owner supervises all projects to ensure high-quality workmanship.
    • Customer Satisfaction Guaranteed!
  • Shingle Roofing: Repairing Valley Leaks in 6 Easy Steps

    Shingle Roofing: Repairing Valley Leaks in 6 Easy Steps

    Though roof valleys are common leak sites on shingle roofs, repairing valley leaks is fairly straightforward to handle if you know what you’re doing.

    Roof valleys are channels designed to drain runoff water, and like any other part of your roof, they can degrade over time with exposure to the elements. In other cases, water can become trapped under shingles that have been overlaid to create the valley trough.

    In either situation, the leaking roof valley can be fixed by removing affected shingles and structural elements and upgrading your roof’s flashing. Flashing is a transitional roofing material that connects the roof material to some other building material or to another part of the roof. And damaged flashing is behind most roof leaks.

    Roof Valley Leak Repairs, Newtown Square, PA 19073
    Roof Valley Leak Repairs, Newtown Square, PA 19073

    Shingle Roofing: Repairing Valley Leaks in 6 Easy Steps

    Prepare For The Repair

    Follow these three preparatory steps to master repairing valley leaks:

    1. Clear any debris in the roof valley and surrounding area and measure your roof flashing — most flashing is 14 inches wide, but yours may vary.
    2. Move to the highest end of the valley and work your way down, cleaning shingles from both sides of the valley whether they’re damaged or not. Experts recommend that you give yourself 8 to 10 inches of clearance on each side of the valley. Use a nail bar to loosen the shingles in the affected area —  insert the bar under a shingle and pry upward at the location of each nail to loosen a nail. Pull out the nails with the bar.
    Roof Replacement, Bear DE

    Repair Damaged Roof Valley

    Here’s how to install new flashing in your roof valleys:

    1. Begin by placing the replacement piece of flashing in the valley lining up the groove in the center with the middle of the valley. Make sure the flashing’s bottom edge is perfectly aligned with your roof’s lower edge. Valley flashing comes in standard lengths, ranging from 8 to 12 feet – if your valley is longer, install the lower piece of flashing first then overlap the lower edge of the next piece by a foot.
    2. Use a metal cutter to alter the length of the flashing to ensure it lines up with your roof’s lower edges. At the top edge of your roof valley, check to make sure the flashing is properly angled to line up with the slope of the roof. Use roofing nails to secure the flashing in place, driving nails at 1-foot  intervals along the outer edges of each side from top to bottom.
    3. Replace all shingles you removed, making sure their edges are at least 1 inch from the elevated center of the flashing piece. Work your way up, starting at the lower edge of the roofing and moving towards the top.
    4. Attach the shingles by nailing the upper edges with the appropriate 1 1/2-inch roofing nails for composition or 5d shingle nails for wood shingles. Trim and install rows of shingles that align with the existing rows at each side of the valley.

    Don’t neglect repairing valley leaks in a timely manner — they can lead to additional structural problems, mold growth, and high levels of moisture and humidity, all of which can be difficult and expensive to repair.

    Need Help Repairing Valley Leaks?

    Repairing a roof valley leak takes experience, and is especially difficult on steep and tile roofs. If you encounter problems, be sure to consult reliable roofing professionals. We can handle these types of repairs quickly and easily, no matter what caused the leak in the first place.

    Call All Roofing Solutions, your full-service roofing repairs contractor with over 20 years of experience in roofing and re-roofing. We will work with you to identify the damage and present you with options tailored specifically to your situation. Our priority is always to provide you with great service!

    Call us at 302-725-7663 in Delaware or 610-551-7663 in Pennsylvania to schedule your FREE repair estimate. And don’t forget to ask about our discount of 15% off any roofing repair projects.

    Why Choose All Roofing Solutions

    • Customer Satisfaction GuaranteedFamily-owned and operated contractor
    • Fully licensed and insured for your protection
    • Over 25 years of experience with roofing & siding installation and repair
    • A+ rated BBB member
    • Complimentary Extended Material warranty
    • 30-year workmanship guarantee on full roof replacements
    • Lien Waiver to protect the homeowners from material liens
    • Own crew—no subcontractors!
    • Full-service roofer handling all types of residential and commercial roofing, windows & siding projects.
    • Most re-roofing projects are completed in one day.
    • Because we are efficient we are able to offer very competitive prices compared to large contractors with bigger overhead.
    • Each roofing/siding project includes a meticulously performed, post-roofing inspection. We want to make sure that your roof replacement is done correctly and that it meets your complete satisfaction.
    • The company owner supervises all projects to ensure high-quality workmanship.
    • Customer Satisfaction Guaranteed!
  • 5 Steps To Ice Dam Damage Repair: How To Fix Ice Dams Fast

    5 Steps To Ice Dam Damage Repair: How To Fix Ice Dams Fast

    Ice dams are a fact of life in Delaware & Pennsylvania—and across America. They can cause major water damage to the exterior and interior as gravity pulls water inside of your home through the wood, insulation, and drywall, causing major structural damage and mold growth.

    Ice dam damage repair can be really tricky. Your best bet against damage from ice dams is to so take the steps necessary to keep dams from forming in the first place. Proper attic insulation & ventilation are the key elements in preventing ice dams from developing—having the right insulation and ventilation will provide the optimal temperature balance in the attic, and prevent the thaw/freeze cycle that causes ice dams.

    But, what do you do when a dam forms, and you see—or suspect—damage? We share the best way to fix ice dams fast today so read on.

    5 Steps To Ice Dam Damage Repair: How To Fix Ice Dams Fast

    Fixing an Ice Dam Fast: 5 Steps to Ice Dam Damage Repair

    If you suspect an ice dam developed on your roof, there are things you can do right away to minimize the damage.

    1. First, get rid of any built up snow using a roof rake (used for single family homes with pitched roofs) or shoveling it off (on flat roofs, or when there’s a significant amount of snow).
    2. Next, remove the ice dam by breaking it free in small chunks. Be very careful here—you don’t want to further damage the roof, or hurt yourself by falling off.
    3. If there’s a leak you notice, blow cold air into the attic to freeze it, aiming it directly at the underside of the roof where water is actively leaking in. This will stop the leak in its tracks.
    4. Even when there are no obvious roof leaks, you’ll want to carefully inspect your roof & gutters when you discover an ice dam. From the attic, check the underside of the roof sheathing and roof trim for moisture in the area beneath the dam. In addition, take a look at the insulation, and see if it’s damp. You’re also looking for other signs of water penetration, including water stains and mold. Take your time to thoroughly inspect your roof.
    5. If you spot problems, have a professional examine your roof surface. Your roofing inspection contractor should be looking for dark patches, missing or damaged shingles, water streaking down the side of the house, signs of uneven melting/freezing, damp attic insulation, sagging boards, signs of mold and mildew—all of these can be signs of ice dam damage. In addition to identifying the source of the leak, your roofing contractor will detail a plan to repair the damage to your roof. If it appears that mold has formed, you’ll also want to contact a contractor who is licensed in identifying and mitigating mold. Mold can be a serious health hazard, and removal is best left to an expert!

    Remember, always keep safety in mind when working on the roof, especially in winter. Or better yet, hire professionals—ice dam damage repairs can be a slow, dangerous work, so hire someone experienced at roofing in all seasons.

    Call Your Local Roofing Contractor

    If you suspect your roof has been damaged and needs repairs—whether because of ice dams or otherwise—the best advice we can give you is to seek out the expertise and advice of an experienced, local roofing contractor. And All Roofing Solutions is ready to help!

    We’re a family-owned business with over 20 years of experience and offer affordable, expert roof repair, replacement, and installation services to customers throughout Delaware and southeastern Pennsylvania. We pride ourselves on outstanding workmanship and great customer service, and have amassed a list of happy customers who love our work!

    Call our DE office at 302-725-ROOF (7663) or our PA location at 610-551-ROOF (7663) for your free repair estimate today! And don’t forget to ask about our discount of 15% off any roof repair job!!!

    Why Choose All Roofing Solutions

    • Customer Satisfaction GuaranteedFamily-owned and operated contractor
    • Fully licensed and insured for your protection
    • Over 25 years of experience with roofing & siding installation and repair
    • A+ rated BBB member
    • Complimentary Extended Material warranty
    • 30-year workmanship guarantee on full roof replacements
    • Lien Waiver to protect the homeowners from material liens
    • Own crew—no subcontractors!
    • Full-service roofer handling all types of residential and commercial roofing, windows & siding projects.
    • Most re-roofing projects are completed in one day.
    • Because we are efficient we are able to offer very competitive prices compared to large contractors with bigger overhead.
    • Each roofing/siding project includes a meticulously performed, post-roofing inspection. We want to make sure that your roof replacement is done correctly and that it meets your complete satisfaction.
    • The company owner supervises all projects to ensure high-quality workmanship.
    • Customer Satisfaction Guaranteed!
  • Handling Leaky Chimneys: Inspection & Repair Tips From a Roofing Contractor

    Handling Leaky Chimneys: Inspection & Repair Tips From a Roofing Contractor

    While roof leaks can occur anywhere on your roof, they commonly develop around chimneys, vents, skylights, and other roof penetrations around the roof.

    Leaky chimney problems can quickly become costly and may include drywall warping, ceiling stains, insulation saturation, mold growth, and interior home damage.

    Don’t make the mistake of ignoring small leaks and risking serious damage in the process — if your notice your chimney leaking during inclement weather, it’s time to schedule a professional roofing inspection.

    Handling Leaky Chimneys: Inspection & Repair Tips From a Contractor

    Why Chimneys Are Susceptible To Leaking

    How do chimney leaks develop in the first place?

    There are 5 major reasons behind chimney leaks:

    • Missing or damaged chimney cap
    • Cracked chimney crown
    • Flashing problems
    • Leaky bricks
    • Faulty chimney liner

    One of the reasons is that, over time, chimneys tend to develop cracks and crevices that allow water to permeate them. Additionally, the sections of metal applied at the seams between the chimney and roof  — called roof flashing — may come loose or break due to high winds and other inclement weather.

    Improper chimney flashing installation can also open up your roof to early deterioration. Chimney leaks are the primary form of damage you will notice from a faulty chimney flashing installation. Instead of keeping rain and snow out of the roof seams, sub-par flashing allows moisture into the roof’s inner structure. Water seepage can cause mildew, mold, and premature aging of the roof.

    To learn more about how chimneys develop leaks read: 5 Reasons Behind A Leaking Chimney

    Handling Leaky Chimneys: Inspection & Repair Tips

    So what can you do? Start by hiring a professional roofing contractor to inspect your structure then handle repairs promptly.

    When your roofer arrives, he will inspect your chimney for any signs of damage:

    • Broken bricks or stone
    • Loose mortar joints
    • Cracks around the chimney foundation
    • Deteriorating flashing
    Chimney Flashing Repair, Wilmington DE 19803

    After a thorough inspection, which will most likely include chimneys, vents, skylights, all areas of flashing, and your home’s drainage systems check, proper repairs will be needed.

    For more tips on proper roofing inspection, check out: Roofing Inspection 101: Contractor’s 3-Step Checklist

    Depending upon the extent of the damage and the cause of the leak, the roofer may seal stone or brick cracks and apply water repellant to prevent further leaks. If the chimney material is not damaged, the leak could be caused by flashing damage. Flashing is a type of metal placed around the chimney base and covered with shingles to prevent water infiltration. Some flashing can be repaired, but if it shows signs of rust or other weather wear, your contractor may need to remove shingles to install new flashing. This is not a do-it-yourself undertaking, since improper flashing installation could void your roof warranty.

    Your local roofer should also check the cement chimney cap for cracks, breaks, or leak causes. If the cap or mortar joints are damaged because of structural shifts, your chimney may require masonry repair.

    To learn more about chimney repair tips: Residential Roofing: 4 Steps To Chimney Leak Repair

    We Handle Chimney Leak Repairs!

    All Roofing Solutions is a family-owned and operated Delaware roofing repair contractor in business since 1998, based in Wilmington, DE. We specialize in residential roof leak repair services in Delaware and bordering Pennsylvania counties.

    Whether you need a chimney, skylight, or valley leak repaired, we are fully licensed and insured and can handle all your roofing repair needs, large and small. Our goal is to deliver superb workmanship and outstanding customer service. We stand behind our work!

    • Customer Satisfaction GuaranteedFamily-owned and operated Delaware & Pennsylvania roofing contractor.
    • Fully licensed and insured.
    • Over 25 years of experience with roofing & siding installation and repair.
    • A+ rated BBB member
    • Complimentary Extended Material warranty
    • 30-year workmanship guarantee on full roof replacements
    • Lien Waiver to protect the homeowners from material liens
    • Own crew—no subcontractors!
    • Full-service roofer handling all types of residential and commercial roofing, windows & siding projects.
    • Most re-roofing projects are completed in one day.
    • Because we are efficient we are able to offer very competitive prices compared to large contractors with bigger overhead.
    • Each roofing/siding project includes a meticulously performed, post-roofing inspection. We want to make sure that your roof replacement is done correctly and that it meets your complete satisfaction.
    • The company owner supervises all projects to ensure high-quality workmanship.
    • Customer Satisfaction Guaranteed!

    If your chimney is leaking or you suspect chimney damage, don’t wait to call All Roofing Solutions, your local Delaware roofing contractor with 20 years of experience in roofing repairs and roof replacement. We offer fast and free estimates and 24-hour emergency service.

    To schedule your FREE repair estimate, call 302-725-ROOF (7663) in Delaware or 610-551-ROOF (7663) in Pennsylvania!